环氧防腐型粉末涂料
一 般 介 绍:采用环氧树脂等防腐材料制备而成的,具有优异的耐化学品性和机械性,用于对耐腐蚀性、电绝缘性和柔韧性有较高要求的金属制品的涂装。一般不建议直接用于各种户外用品的表面涂装。工作流 主要用于输···
13901502010 在线咨询一 般 介 绍:采用环氧树脂等防腐材料制备而成的,具有优异的耐化学品性和机械性,用于对耐腐蚀性、电绝缘性和柔韧性有较高要求的金属制品的涂装。一般不建议直接用于各种户外用品的表面涂装。工作流 主要用于输···
13901502010 在线咨询一 般 介 绍:采用环氧树脂等防腐材料制备而成的,具有优异的耐化学品性和机械性,用于对耐腐蚀
性、电绝缘性和柔韧性有较高要求的金属制品的涂装。一般不建议直接用于各种户外用品的表面涂装。工作流 主要用于输油管道,及化工设备的防腐涂装。 应用服务器
产 品 系 列:可提供标准型和固化型粉末涂料产品。可做成高光(80%以上)、半光(50-80%)、平光(20-50%)和无光(20%以下)的产品(可根据用户的需求控制光泽)。 试验机
粉末物理性能:比重(g/cm3、25℃):1.4-1.7 粒度分布: 100%小于100微米(可根据涂装的特殊要求进行调整)
固 化 条 件:A型 200℃ (工作温度),10分钟
B型 180℃ (工作温度),15分钟
C型 140℃ (工作温度),20分钟
平均覆盖率:9-12平方米/公斤,膜厚60微米(以100%的粉末涂料使用率计算)。
涂膜性能:
检测项目 | 检验标准或方法 | 检验指标 | |
A型 | B、C型 | ||
抗冲击性 | GB/T 1732-1993 | 40kg.cm | 50kg.cm |
杯突实验 | GB 9753-1988 | 5mm | 8mm |
附着力(划格法) | GB/T 9286-1998 | 0级 | |
弯曲 | GB 6742-1986 | 3mm | 2mm |
铅笔硬度 | GB/T 6739-1996 | 1H-2H | |
盐雾实验 | GB 1771-1991 | >500小时 | |
湿热实验 | GB 1740-1989 | >1000小时 | |
乃热性 | 100℃×24小时(白色) | 保光性优异,色差≤0.3-0.4 | |
注 | 1.以上实验采用0.8毫米厚经标准前处理的冷轧钢板,涂膜厚度为60-80微米。 升降机 | ||
2.以上涂膜的性能指标可能会随着美术效果和树脂类型的不同而有所变化。 标记机 |
Epoxy powder coatings(环氧防腐型粉末涂料)
General introduction
This type of coating is prepa red from the epoxy resin, and it has excellent chemical resistance and good mechanical prope rties. It is suiltable for the coating of metallic appliances that has rigor demand on the anti-corrosion , insulating properties and flexibility. It is suggested to use this type of coating directly in the coating for outdoor appliances.
Product Series
Standard and low temperature solidification type powder coating can be provided.
Physical properties of the powder
Density(g/cm3,25℃):1.4-1.7
Granularity distribution:100%below 100μm(it can be adapted to the customers’demand)
Curing Condition
Type A 200℃(workpiece temperature),10minutes(flat gloss or no gloss )
Type B 180℃(workpiece temperature),15minutes(high gloss or semi gloss )
Type C 140℃(workpiece temperature),20minutes(high gloss )
Average coating rate
9-12㎡/kg, film thickness:60μm (calculated according to 100% consuming of powder coating)
Coating performance
Testing items | Standards and methods | Inspecting index | |
Type A | Type B | ||
Impact strength | GB/T 1732-1993 | 40kg.cm | 50kg.cm |
ERICHSEN TEST | GB 9753-1988 | 5mm | 8mm |
Adhesion(CHECKED TEST) | GB/T 9286-1998 | Grade0 | |
Bending resistance | GB 6742-1986 | 3mm | 2mm |
Pencil hardness | GB/T 6739-1996 | F-H | |
Salt mist resistance | GB 1771-1991 | >500h | |
Heat & moisr resistance | GB 1740-1989 | >1000h | |
Heat resistance | 100℃×24h(white color) | Good gloss retention, Aberration≤1 | |
Notations | ⒈The tests above used the cold rolling steel plate of 0.8mm thick with preceding standard treatment. The thickness of the coaring layer is 60-80μm | ||
2. The above performance index may slightly decrease with the decreasing of the gloss. |